Provide high-quality products and excellent services to customers around the world.
-
PRODUCT
-
PRODUCT
Thrust ball bearings are designed to withstand thrust loads at high speeds and are composed of gasket rings with ball rolling raceway grooves. Because the ring is the seat pad shape, the thrust ball bearing is divided into two types: flat base pad type and aligning spherical seat type. In addition, this bearing can withstand axial loads, but not radial loads.
Double direction thrust ball bearing
Two-ways thrust ball bearings consist of a shaft washer, two races and two steel ball cage assemblies. The bearing is a split type, and each part can be installed independently. Two-way and one-way bearings use the same shaft washer, seat washer and ball cage assembly.
Thrust ball bearing is a separable bearing, the shaft washer and seat washer can be separated from the cage and steel ball parts. The collar is a ferrule matched with the shaft, the seat ring is a ferrule matched with the bearing seat hole, and there is a gap between the shaft and the shaft. Imported thrust ball bearings have more structural modifications and are special bearings used to withstand axial forces. Thrust bearing is also called thrust bearing.
Thrust Roller bearing is a rolling-element bearing of thrust type that permits rotation with low friction, and permits angular misalignment. The bearing is designed to take radial loads, and heavy axial loads in one direction.
Thrust roller bearings are used to bear axial load mainly combined axial and radial load, but the radial load shall not exceed 55% of the axial load. Compared with other thrust roller bearings, this bearing has lower friction factor, higher speed and aligning performance.
Thrust roller bearings are used to bear axial load mainly combined axial and radial load, but the radial load shall not exceed 55% of the axial load. Compared with other thrust roller bearings, this bearing has lower friction factor, higher speed and aligning performance.
Thrust Roller bearing is a rolling-element bearing of thrust type that permits rotation with low friction, and permits angular misalignment. The bearing is designed to take radial loads, and heavy axial loads in one direction.
The stick of type 29000 bearing is asymmetrical spherical roller, which can reduce the relative sliding of roller and raceway in the work, and the roller is long, large diameter, large number of rollers, high load capacity, usually using oil lubrication, individual low speed can be lubricated by grease. In the design and selection, should be preferred.
51324 Thrust Ball Bearing For Water Pump
Peculiarity: 1. There are two types, one-way and two-way 2. In order to allow for installation error, whether one-way or two-way, you can choose spherical aligning spherical seat cushion type or spherical seat ring type. 3. High-quality steel: The use of ultra-clean steel that can extend the bearing life by up to 80% 4. High grease technology: NSK's lubricant technology can extend the life of the grease and improve the performance of the bearing 5. High-grade steel ball: quiet and smooth when rotating at high speed 6.Use the collar in the option to allow installation errors There are two key points in the assembly of thrust ball bearings. One is the control of the pressing quality of the cage and the steel ball, and the other is the control of the nominal height T after the assembly of the bearing. In addition, since the shaft ring and the seat ring can be separated, there is a management problem. It is to prevent the mixing of imported bearing parts. The M-type press cage uses a curved edge assembly die. After pressing, the steel ball is required to rotate flexibly in the pocket hole, but it can not fall off from the pocket hole, and the technical procedure to check the momentum of the steel ball in the pocket hole. If the solid cage is imprinted too deeply, the momentum of the steel ball will be small, and the connection between the embodiments and the cage is too little and the strength is insufficient, which is easy to fall off and cause the cage to be scrapped. Structure: The thrust ball bearing is composed of race, shaft washer and steel ball retainer. The one that matches with the axis is called washer. The one that matches with the shell is called the ring. Thrust ball bearing is a kind of separation bearing. The shaft ring and seat ring can be separated from the cage and steel ball components. Thrust ball bearing is designed to withstand thrust load at high speed and is composed of a gasket-shaped ring with a ball rolling groove. Owing to its cushion-shape ring, the thrust ball bearing is divided into flat-base cushion type and aligning spherical surface cushion type.
Thrust ball bearings are designed to take axial (thrust) loads at high speeds, but they cannot take any radial loads. These bearings feature bearing washers with raceway grooves in which the balls move.
CONTACT US
Address:Room 2-A010, Building 26, Zone 3, Times Headquarters Base, No. 15, Lanxiang Road, Tianqiao District, Jinan City, Shandong Province
PRODUCTS
◆
◆
Copyright © Shandong Aifule Precision Bearing Co., Ltd.